Banner_2
Print

Acrylic Cast

The Vulcan full acrylic cast

The special Vulcan acrylic cast guarantees the best quality. Vulcan is especially designed for use in humid, wet, very cold or very hot areas.

kalk_scale_green_point The acrylic cast ensures that the circuit board is protected. The parts are fully covered in acrylic. Therefore the parts can not move and are fixed in place. This guarantees a high life expectancy.

kalk_scale_green_point It protects the unit from humidity e.g. when installed outdoor

kalk_scale_green_point The full body acrylic cast protects from dust and dirt
e.g. when installed in a basement

kalk_scale_green_point The full body acrylic cast protects against heat and protects against coldness as acrylic is a perfect isolating material. E.g. when installed in extremely hot areas with outdoor temperature up to 45-50°C (~113- 122 °F) or in very cold temperatures down to -20°C (~5°F).

kalk_scale_green_point The acrylic cast ensures a very long product life.
The Vulcan's solid acrylic isolating material ensures that the electricity does not "blow" as the electronic block is perfectly isolated from the inside as well.
The most common cause of a malfunction in electronic devices is that they "blow" when the electricity heats up too much. The thick acrylic covering together with the vacuum prevents heat production. This "cooling" of the unit ensures a long life.


  acrylic-cast-thumb
     

Impulse Bands

The Vulcan Impulse Bands

Vulcan operates with customized isolated copper impulse bands that are designed to firmly connect to the pipe. They are extremely thin and flexible with minimized isolation. This way, they achieve minimal spacing loss and maximize the direct-contact-ratio to 97.5%. Their special copper material with a high alloy purity degree guarantees the best possible transfer output. The copper treatment bands are a crucial factor to the performance of the water treatment.

The pipe diameter/treatment area ratio
The impulse bands cover the surface area that is vital for the treatment. The surface of the pipe that is covered by the impulse band is the "treatment area". This area needs to be large enough to ensure that the impulses are transmitted through the pipe. As a general rule each impulse band should cover a treatment area of at least the length of the individual pipe diameter where Vulcan is to be installed.


Example:
If you install a Vulcan 5000 on a 2” pipe, each impulse band should cover a pipe length of min. 2”.

vulcan-example-impulse-bands
  impulse-bands



Treatment with standard cables vs. impulse band

        Other cables       Vulcan impulse bands

impulse-bands-treatment-areatreatment-areaTreatment Area

Comparison: The Vulcan Impulse Bands accumulate more direct contact compared to round cables as there is less spacing. The direct contact ratio reaches 97.5%.
     

Certifications

German Quality Certifications

   
ul-logo
UL Approval
The UL - Underwriters Laboratories Inc. - is an international quality and safety approval institution with headquarters in Illinois, USA. The UL-mark on a product states that UL has tested and evaluated the product and determined that the electronics fulfil the strict safety guidelines. All Vulcan switching power adaptors are meeting these requirements and comply with international standards.
  ul-letter
     
Line_Gray
Line_Gray
     
tuv-logo
The German TÜV/GS
The "German TÜV" is a independent institution that assesses products for safety and reliability. When a product passes the strict regulations it is awarded the TÜV/GS mark which indicates that the product was tested and certified for safety according to the "German Equipment Safety Law". The GS mark is a certification that includes periodic factory inspections covering the quality system for the product's production. This law requires inspectors to frequently assess whether the manufacturer is able to maintain all the specifications of the tested product in his production. During this factory inspection, the implementation of the quality system, the production environment, and production related testing and measurement equipment is evaluated.
  tuv-letter
     
Line_Gray
Line_Gray
     
ce-logo
CE Approval
The CE mark certifies that a product has met German and European Union consumer safety, health or environmental requirements. "CWT hereby declares that this product is operating in accordance with the following EU-guidelines: 73/23/EG; 89/336/EG which is certified by the CE-mark. The equipment corresponds to the requirements of the German Industrial Safety Act and the European low-voltage guidelines."
  ce-letter
     
Line_Gray
Line_Gray
     
ihk-logo
Certificate of Origin: Germany
The Certificate of Origin (CO) names and officially approves the country where the goods are actually produced. For Germany the certificate is issued by the German Chamber of Commerce (IHK). It approves the German origin (Made in Germany) after thorough investigation of the origin of each individual part of the product and after assessment of the production site in Germany.
  origin-letter
     
Line_Gray
Line_Gray
     
made-in-germany-product